Exact product identification
Your quotation references the complete manufacturer part number to keep the requested product clear.

WTB9-3P1161
W9 red-light background-suppression sensor with PNP complementary light/dark output. 20–350 mm on white targets, 20–200 mm on black; cable, 4-wire, 2 m. 10–30 V DC, 5-turn distance adjustment and M3 mounting.
Warranty coverage and terms are confirmed with your order.
We coordinate the fastest available shipping option for your destination.
Available payment methods are handled through secure payment channels.
Carrier and delivery options are confirmed for your destination before dispatch.
Independent supplier: Xindustra is not an authorized distributor, reseller, or representative of SICK. Brand names are used for identification and compatibility purposes only. Read disclaimer
Sensing conditions, PNP output logic and installation data for WTB9-3P1161.
WTB9-3P1161 detects objects from their reflected light and suppresses backgrounds beyond its adjusted sensing distance. The visible-red PinPoint LED helps align the small light spot. It is a self-contained proximity sensor: no separate reflector or opposing receiver is needed.
Photoelectric proximity, background suppression
Visible-red PinPoint LED
650 nm
20–350 mm
90% remission, based on standard white DIN 5033.
20–200 mm
6% remission; 350 mm is not the black-target range.
Ø 4.5 mm at 75 mm
5-turn potentiometer
Place the target inside the sensing range for its reflectance and set the switching distance ahead of the background. A dark part near 200 mm leaves less optical margin than a white part at the same distance. Keep the spot on the feature being detected; the spot grows with distance.
Light spot versus distance
Original SICK WT9-3 red-light, 350 mm optical diagram. The nominal spot is Ø 4.5 mm at 75 mm; dimensions are in millimetres.
Reflectance-dependent sensing range
Original SICK range diagram: black 6%, gray 18% and white 90% remission. These are reference targets, not a guarantee for every surface finish.
WTB9-3P1161 provides PNP Q and complementary not-Q outputs. Q is light switching: it turns on when an object is detected; not-Q provides the opposite state. The output sources current to a PLC input referenced to 0 V. Select the PLC input circuit to match this output type.
10–30 V DC
<5 Vpp
Supply must remain within the 10–30 V DC limits.
30 mA
Without load.
PNP
Complementary Q / not-Q, light/dark switching
≤100 mA
At and above 50 °C, maximum load current is 50 mA.
<0.333 ms
Signal transit time with resistive load.
1,500 Hz
Light/dark ratio 1:1.
Supply and I/O reverse-polarity protection; interference suppression
III
Cable, 4-wire, 2 m
+L, positive DC supply
M, 0 V common
Q, light-switching output
not-Q, complementary dark-switching output
PVC
0.14 mm²
| Parameter / condition | Object detected | No object detected |
|---|---|---|
| Q | ON | OFF |
| not-Q | OFF | ON |
PNP ON sources current toward +L. OFF is the inactive switching state, not a separately driven opposite voltage. Connect the output whose logic matches the control task.
The fixed 2 m cable connects directly to the machine wiring. BN and BU supply the sensor; BK carries Q, and WH carries not-Q. Do not bend the PVC cable below 0 °C.
WTB9-3P1161
1049043
W9
12.2 × 50 × 23.6 mm
M3, Ø 3.1 mm
VISTAL plastic
PMMA plastic
80 g
IP66 / IP67 / IP69K
−40 to +60 °C
Output load restricted to 50 mA at and above 50 °C.
−40 to +75 °C
Align the optical face with the detection area and leave access to the top potentiometer. The green LED indicates power and the yellow LED indicates received-light status. Position the sensor so that the target occupies the light spot while the background stays beyond the switching threshold.
WTB9-3P1161 is SICK part number 1049043, with PNP complementary output and cable, 4-wire, 2 m. Other W9 type codes can change the optical principle, output, connection or mounting size. This cable-body configuration is not an IO-Link version or a W9 laser sensor.
Manufacturer data and the resource page for this exact order number.
Order the exact product and condition your project requires, with assistance from quotation through delivery.
Your quotation references the complete manufacturer part number to keep the requested product clear.
Tell us whether you need new original, new surplus, used, refurbished or repaired equipment.
Shipping options are prepared around your destination, quantity and requested delivery date.
Access available manufacturer product data, manuals and certificates associated with the order number.