Exact product identification
Your quotation references the complete manufacturer part number to keep the requested product clear.
ABB AF26-30-00-13 3-Pole Contactor
AF26-30-00-13
Three-pole AF contactor with 100–250 V AC/DC electronic coil and screw terminals. 11 kW / 26 A at 380–400 V AC-3; no fitted auxiliary contacts.
- Availability
- In Stock
- Condition
- New Original
- SKU
- AF26-30-00-13
- Lifecycle
- Active
12 months warranty
Warranty coverage and terms are confirmed with your order.
Fast shipping
We coordinate the fastest available shipping option for your destination.
Secure payment
Available payment methods are handled through secure payment channels.
Worldwide delivery
Carrier and delivery options are confirmed for your destination before dispatch.
Independent supplier: Xindustra is not an authorized distributor, reseller, or representative of ABB. Brand names are used for identification and compatibility purposes only. Read disclaimer
Technical specifications
Load selection, control circuit and installation data for AF26-30-00-13.
Switching three-phase motor and power circuits
The AF26-30-00-13 is a non-reversing contactor with three normally open main poles. Its 11 kW motor rating applies at 380–400 V AC in the AC-3 utilization category. The electronic control circuit accepts either AC or DC within its specified range.
Ordered configuration
- Type
AF26-30-00-13
- ABB order code
1SBL237001R1300
- Main contacts
3 NO
- Fitted auxiliary contacts
0 NO, 0 NC
- AC-3 motor power, 380–400 V
11 kW
- AC-3 operating current, 380–400 V
26 A; air close to contactor ≤60 °C
- AC-1 operating current
45 A at ≤40 °C, Ue ≤690 V
- Coil suffix
13
- Control voltage
100–250 V AC, 50/60 Hz; 100–250 V DC
Use the rating for the actual load
AC-3 covers starting and switching running squirrel-cage motors; AC-1 describes non-inductive or slightly inductive loads. The AC-1 current is not a motor-current rating. Voltage, utilization category and temperature affect the permitted load, so a rating at 400 V does not transfer unchanged to 690 V.
Build a coordinated motor starter
A contactor switches the load; it does not provide motor overload or short-circuit protection. Combine it with the appropriate overload protection and upstream protective device. Select the tested coordination combination for the prospective fault current and motor duty.
One wide-range AC/DC coil
The -13 electronic coil is rated 100–250 V for both AC and DC operation. This is the control-circuit rating, separate from the main power circuit. Built-in surge suppression is part of the AF design.
Add feedback contacts when required
The -30-00 configuration has no fitted NO or NC auxiliary contacts. Add a suitable auxiliary block if the control scheme requires feedback, interlocking or a holding contact.
Use an appropriate control interface
These standard AF models are not the AF..Z versions designed for direct PLC-output control. Drive the 100–250 V coil through a control device rated for its voltage and switching duty.
Circuit roles
- Coil terminals
A1 / A2
- Main power paths
1L1–2T1, 3L2–4T2, 5L3–6T3
Standard body and main terminals
- Width × height × depth
45 × 80 × 86 mm
- Mounting
35 mm DIN rail
- Main terminal style
Screw terminals with cable clamp
- Main conductor stripping length
14 mm
- Main terminal tightening torque
2.5 N·m
- Coil terminal tightening torque
1.2 N·m
ABB dimensional drawing
Catalog 3/42; select the AF26 drawing. Dimensions are mm and inches. Allow additional space for accessories and conductors.
ABB conductor and terminal data
Catalog 3/102. Use the AF26 column and the row for the actual conductor and ferrule. Main and coil terminals have different torque values.
Match conductor preparation to the terminal
Use the listed conductor cross-section for the cable type, number of conductors and ferrule arrangement. Tighten unused terminal screws as specified. Keep the main-power and control connections distinct; fitted accessories can change the installation envelope.
Downloads and documentation
Sourcing and order support
Order the exact product and condition your project requires, with assistance from quotation through delivery.
Condition options
Tell us whether you need new original, new surplus, used, refurbished or repaired equipment.
International delivery
Shipping options are prepared around your destination, quantity and requested delivery date.
Documentation support
Access available manufacturer product data, manuals and certificates associated with the order number.