Skip to content
Siemens SIMATIC ET 200SP DQ 8x24VDC/0.5A ST digital output module

Siemens ET 200SP DQ 8x24VDC/0.5A ST 6ES7132-6BF01-0BA0

6ES7132-6BF01-0BA0

Eight-channel Standard 24 V DC PNP output module, 0.5 A per channel and 4 A total. Module-wise wire-break and short-circuit diagnostics, substitute values and optional QI.

Availability
In Stock
Available quantity
12 units
Condition
New Original
SKU
6ES7132-6BF01-0BA0
Lifecycle
Active
$67.00
Request a quote
Ask a product question

12 months warranty

Warranty coverage and terms are confirmed with your order.

Fast shipping

We coordinate the fastest available shipping option for your destination.

Secure payment

Available payment methods are handled through secure payment channels.

Worldwide delivery

Carrier and delivery options are confirmed for your destination before dispatch.

Independent supplier: Xindustra is not an authorized distributor, reseller, or representative of Siemens. Brand names are used for identification and compatibility purposes only. Read disclaimer

Technical specifications

Output ratings, load limits and configuration for the DQ 8x24VDC/0.5A ST.

Eight Standard outputs with load-wiring diagnostics

An eight-channel Standard PNP output module rated 0.5 A per channel. Compared with the Basic output variant, it reports module-wise wire break and short circuits to M or L+, and can provide value-status information alongside the output data.

Output electrical ratings

Digital outputs

8

Output logic

PNP, current-sourcing

Nominal output voltage

24 V DC

Rated current per channel

0.5 A

Maximum module output current

4 A

Within the stated horizontal and vertical temperature limits

Maximum lamp load per channel

5 W

Load resistance range

48 Ω to 12 kΩ

Residual current at signal 0, maximum

0.1 mA

Short-circuit protection

Electronic

Typical short-circuit response threshold

0.7–1.3; typical 1 A

Output delay 0 → 1 / 1 → 0

50 / 100 µs maximum at rated resistive load

The protection threshold is not the rated load current

The 0.5 A channel rating is the usable load-current limit. The electronic short-circuit response threshold is a protection characteristic, not permission to operate a channel above its rated current. Fault diagnostics provide an additional troubleshooting function; they do not increase the channel rating.

Total-current limits

Horizontal installation, through +60 °C

4 A

Vertical installation, through +50 °C

4 A

Switching limits

Resistive-load switching frequency, maximum

100 Hz

Inductive-load switching frequency

0.1 Hz

Higher rates depend on load current and the permitted switching-frequency curve in the module manual

Lamp-load switching frequency, maximum

10 Hz

Inductive shutdown-voltage limitation

Typically L+ − 50 V

Parallel outputs for increased current

Not permitted

Parallel outputs for redundant load control

Supported

Disable “Short circuit to L+” and “Wire break” diagnostics for the paired outputs to avoid false diagnostic messages

Size the load for its electrical behavior

The maximum total remains 4 A through +60 °C horizontally or +50 °C vertically. For inductive loads, the data sheet lists 0.1 Hz, with higher rates governed by the manual’s current-dependent curve. This differs from the Basic variant’s switching specification.

Supply and electrical separation

Load supply L+

24 V DC

Permissible range: 19.2–28.8 V DC

Reverse polarity protection

Yes

Module current consumption, maximum

20 mA

Without load current

Typical power loss

1 W

Channel-to-channel isolation

No

Isolation from backplane bus

Yes

Shielded cable length, maximum

1000 m

Unshielded cable length, maximum

600 m

BaseUnit requirements by actuator wiring

BaseUnit requirements by actuator wiring
Parameter / conditionBaseUnit arrangement
1-wireBU type A0
2-wireBU type A0
3-wireBU type A0 with AUX terminals, or a potential distributor module
4-wireBU type A0 plus a potential distributor module

Start or continue the potential group

A light-colored BaseUnit starts a new potential group; a dark-colored BaseUnit continues the voltage buses from the module on its left. Select the module’s potential-group parameter to match the physical BaseUnit arrangement. The electronic module and BaseUnit are separate order items.

Terminal arrangement

Outputs DQ0–DQ7 map to terminals 1–8. The remaining terminals 9–16 are common M return connections, not additional outputs. Use the BaseUnit connection matrix when additional conductor terminations are required.

Output circuit and terminal assignment

Schematic circuit diagram

02/2025 · A5E03574575-AG, Figure 4-1. Original output circuit, terminal mapping, supply and backplane-bus connections.

Schematic circuit diagram

Siemens DQ 8x24VDC/0.5A ST schematic circuit diagram with terminal markings and circuit legend

02/2025 · A5E03574575-AG, Figure 4-1. Original output circuit, terminal mapping, supply and backplane-bus connections.

Diagnostic capabilities

Supply voltage monitoring

Supported

Wire-break diagnostics

Module-wise

Short-circuit to M / L+ diagnostics

Module-wise

Dedicated channel fault LEDs

No

Substitute-value output

Supported

PWM / oversampling

Not supported

MSO

Not supported

Firmware update

Not supported

Isochronous operation

Not supported

Address space

1 byte plus 1 byte for QI

Engineering system support

Engineering system support
Parameter / conditionSupported version / integration
STEP 7 TIA PortalV14 with HSP0222; integrated from V15
STEP 7 ClassicV5.5 SP3 with HSP0230 V7.0; integrated from V5.6 SP1
PCS 7V8.1 SP1
PROFINETGSDML V2.3
PROFIBUSSeparate GSD files, revisions 3 and 5 or later

Standard diagnostics are module-wise

Diagnostic messages identify a module fault rather than a dedicated red fault LED for each channel. Configure substitute values and QI according to the process requirements. In TIA Portal V14, use HSP0222; the module is integrated from V15.

Module dimensions and operating conditions

Dimensions W × H × D

15 × 73 × 58 mm

Electronic module; excludes BaseUnit and packaging

Approximate module weight

30 g

Horizontal operating temperature

−30 to +60 °C

Operation below 0 °C requires hardware status FS02 or later

Vertical operating temperature

−30 to +50 °C

Operation below 0 °C requires hardware status FS02 or later

Maximum installation altitude

5000 m

Above 2000 m, additional installation restrictions apply as described in the ET 200SP system manual

Color code

CC02

Mechanical coding

Type A

Packing unit

1 module

What this order number includes

6ES7132-6BF01-0BA0 identifies the DQ 8x24VDC/0.5A ST electronic module in a one-piece packing unit. Order the type A0 BaseUnit separately for the intended wiring arrangement. This is a standard digital I/O module, not a fail-safe I/O module, interface module or complete ET 200SP station.

Sourcing and order support

Order the exact product and condition your project requires, with assistance from quotation through delivery.

Exact product identification

Your quotation references the complete manufacturer part number to keep the requested product clear.

Condition options

Tell us whether you need new original, new surplus, used, refurbished or repaired equipment.

International delivery

Shipping options are prepared around your destination, quantity and requested delivery date.

Documentation support

Access available manufacturer product data, manuals and certificates associated with the order number.