Skip to content
Siemens SIMATIC ET 200SP DQ 8x24VDC/0.5A BA digital output module

Siemens ET 200SP DQ 8x24VDC/0.5A BA 6ES7132-6BF01-0AA0

6ES7132-6BF01-0AA0

Eight-channel Basic 24 V DC PNP output module rated 0.5 A per channel and 4 A total. Electronic protection, supply diagnostics and substitute-value output; type A0 BaseUnits.

Availability
In Stock
Available quantity
12 units
Condition
New Original
SKU
6ES7132-6BF01-0AA0
Lifecycle
Active
$82.00
Request a quote
Ask a product question

12 months warranty

Warranty coverage and terms are confirmed with your order.

Fast shipping

We coordinate the fastest available shipping option for your destination.

Secure payment

Available payment methods are handled through secure payment channels.

Worldwide delivery

Carrier and delivery options are confirmed for your destination before dispatch.

Independent supplier: Xindustra is not an authorized distributor, reseller, or representative of Siemens. Brand names are used for identification and compatibility purposes only. Read disclaimer

Technical specifications

Output ratings, load limits and configuration for the DQ 8x24VDC/0.5A BA.

Eight Basic PNP outputs for ordinary switching

This Basic module switches eight 24 V DC loads at up to 0.5 A per channel and 4 A total. It offers electronic short-circuit protection and substitute-value output, but diagnostic reporting is limited to supply voltage rather than individual load wiring faults.

Output electrical ratings

Digital outputs

8

Output logic

PNP, current-sourcing

Nominal output voltage

24 V DC

Rated current per channel

0.5 A

Maximum module output current

4 A

Within the stated horizontal and vertical temperature limits

Maximum lamp load per channel

5 W

Load resistance range

48 Ω to 100 kΩ

Residual current at signal 0, maximum

10 µA

Short-circuit protection

Electronic

Typical short-circuit response threshold

1 A

Output delay 0 → 1 / 1 → 0

100 / 150 µs maximum at rated resistive load

The protection threshold is not the rated load current

The 0.5 A channel rating is the usable load-current limit. The electronic short-circuit response threshold is a protection characteristic, not permission to operate a channel above its rated current. Electronic channel protection is present, but this Basic module does not report wire-break or short-circuit diagnostics.

Total-current limits

Horizontal installation, through +60 °C

4 A

Vertical installation, through +50 °C

4 A

Switching limits

Resistive-load switching frequency, maximum

100 Hz

Inductive-load switching frequency

2 Hz

Maximum stated value

Lamp-load switching frequency, maximum

10 Hz

Inductive shutdown-voltage limitation

Typically L+ − 50 V

Parallel outputs for increased current

Not permitted

Parallel outputs for redundant load control

Supported

Size the load for its electrical behavior

Use the 0.5 A channel and 4 A module limits together. This module’s data sheet lists a 2 Hz maximum for inductive loads and a 10 Hz maximum for lamps; select the switching rate by load type, not only by the 100 Hz resistive rating.

Supply and electrical separation

Load supply L+

24 V DC

Permissible range: 19.2–28.8 V DC

Reverse polarity protection

Yes

Module current consumption, maximum

45 mA

Without load current

Typical power loss

1 W

Channel-to-channel isolation

No

Isolation from backplane bus

Yes

Shielded cable length, maximum

1000 m

Unshielded cable length, maximum

600 m

BaseUnit requirements by actuator wiring

BaseUnit requirements by actuator wiring
Parameter / conditionBaseUnit arrangement
1-wireBU type A0
2-wireBU type A0
3-wireBU type A0 with AUX terminals, or a potential distributor module
4-wireBU type A0 plus a potential distributor module

Start or continue the potential group

A light-colored BaseUnit starts a new potential group; a dark-colored BaseUnit continues the voltage buses from the module on its left. Select the module’s potential-group parameter to match the physical BaseUnit arrangement. The electronic module and BaseUnit are separate order items.

Terminal arrangement

The eight output signals occupy terminals 1–8; terminals 9–16 provide M return connections in the one- and two-wire diagram. Three-wire arrangements require AUX terminals or a potential distributor module.

Output circuit and terminal assignment

One- and two-wire actuator wiring

02/2019 · A5E36107249-AB, Figure 3-1. Original actuator wiring and block diagram, including all terminal numbers, supply buses and legend.

One- and two-wire actuator wiring

Siemens DQ 8x24VDC/0.5A BA one- and two-wire actuator wiring with terminal markings and circuit legend

02/2019 · A5E36107249-AB, Figure 3-1. Original actuator wiring and block diagram, including all terminal numbers, supply buses and legend.

Diagnostic capabilities

Supply voltage monitoring

Supported

Wire-break diagnostics

Not supported

Short-circuit to M / L+ diagnostics

Not supported

Dedicated channel fault LEDs

No

Substitute-value output

Supported

PWM / oversampling

Not supported

MSO

Not supported

Firmware update

Not supported

Isochronous operation

Not supported

Address space

1 byte

Engineering system support

Engineering system support
Parameter / conditionSupported version / integration
STEP 7 TIA PortalV14
STEP 7 ClassicV5.5 SP3
PROFINETGSDML V2.3
PROFIBUSSeparate GSD files, revisions 3 and 5 or later

Protection is not diagnostic reporting

Electronic protection responds to a channel short circuit, but the Basic module does not report wire-break or short-circuit diagnostics. Select a diagnostic-capable variant when maintenance must distinguish load-wire faults. Firmware update, MSO and isochronous operation are not supported.

Module dimensions and operating conditions

Dimensions W × H × D

15 × 73 × 58 mm

Electronic module; excludes BaseUnit and packaging

Approximate module weight

30 g

Horizontal operating temperature

−30 to +60 °C

Operation below 0 °C requires hardware status FS02 or later

Vertical operating temperature

−30 to +50 °C

Operation below 0 °C requires hardware status FS02 or later

Maximum installation altitude

5000 m

Above 2000 m, additional installation restrictions apply as described in the ET 200SP system manual

Color code

CC02

Mechanical coding

Type A

Packing unit

1 module

What this order number includes

6ES7132-6BF01-0AA0 identifies the DQ 8x24VDC/0.5A BA electronic module in a one-piece packing unit. Order the type A0 BaseUnit separately for the intended wiring arrangement. This is a standard digital I/O module, not a fail-safe I/O module, interface module or complete ET 200SP station.

Sourcing and order support

Order the exact product and condition your project requires, with assistance from quotation through delivery.

Exact product identification

Your quotation references the complete manufacturer part number to keep the requested product clear.

Condition options

Tell us whether you need new original, new surplus, used, refurbished or repaired equipment.

International delivery

Shipping options are prepared around your destination, quantity and requested delivery date.

Documentation support

Access available manufacturer product data, manuals and certificates associated with the order number.