Skip to content
Siemens SIMATIC ET 200SP DI 8x24VDC BA digital input module

Siemens ET 200SP DI 8x24VDC BA 6ES7131-6BF01-0AA0

6ES7131-6BF01-0AA0

Eight-channel Basic 24 V DC digital input module for PNP signals. Offers configurable input filtering, supply-voltage diagnostics and type A0 BaseUnit wiring.

Availability
In Stock
Available quantity
12 units
Condition
New Original
SKU
6ES7131-6BF01-0AA0
Lifecycle
Active
$61.00
Request a quote
Ask a product question

12 months warranty

Warranty coverage and terms are confirmed with your order.

Fast shipping

We coordinate the fastest available shipping option for your destination.

Secure payment

Available payment methods are handled through secure payment channels.

Worldwide delivery

Carrier and delivery options are confirmed for your destination before dispatch.

Independent supplier: Xindustra is not an authorized distributor, reseller, or representative of Siemens. Brand names are used for identification and compatibility purposes only. Read disclaimer

Technical specifications

Signal characteristics, sensor wiring and configuration for the DI 8x24VDC BA.

Basic acquisition of eight PNP signals

An eight-channel Basic input module for 24 V DC switches and PNP sensors. Choose it for ordinary digital acquisition when supply-voltage monitoring is sufficient; it does not provide the wire-break diagnostics of the Standard variant.

Signal characteristics

Digital inputs

8

Input logic

Sinking input for PNP signals (P-reading)

IEC 61131 input characteristic

Type 2; data sheet also lists types 1 and 3

Nominal input voltage

24 V DC

Signal 0 voltage range

−30 to +5 V

Referenced to M

Signal 1 voltage range

+11 to +30 V

Referenced to M

Typical input current at signal 1

6.8 mA

Configurable input delay

0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms

Additional line-length-dependent delay: 30–500 µs

2-wire sensor quiescent current, maximum

2 mA

Shielded cable length, maximum

1000 m

Unshielded cable length, maximum

600 m

Match sensor current as well as signal voltage

This Basic module draws a typical 6.8 mA at signal 1 and permits up to 2 mA quiescent current from a two-wire sensor. These values differ from the 2.5 mA input current and 1.5 mA sensor quiescent-current limit of the Standard module.

BaseUnit requirements by sensor wiring

BaseUnit requirements by sensor wiring
Parameter / conditionBaseUnit arrangement
1-wireBU type A0
2-wireBU type A0
3-wireBU type A0 with AUX terminals, or a potential distributor module
4-wireBU type A0 plus a potential distributor module

Eight sensor-supply terminals, one total-current limit

The module provides eight sensor-supply outputs. Their combined load must remain within the 700 mA module limit; the per-channel figure does not create an eight-times-higher supply budget.

Start or continue the potential group

A light-colored BaseUnit starts a new potential group; a dark-colored BaseUnit continues the voltage buses from the module on its left. Select the module’s potential-group parameter to match the physical BaseUnit arrangement. The electronic module and BaseUnit are separate order items.

Terminal assignment and signal path

One- and two-wire sensor wiring

02/2019 · A5E34941724-AB, Figure 3-1. Original wiring and block diagram, including terminal numbers, voltage buses and the complete legend.

One- and two-wire sensor wiring

Siemens DI 8x24VDC BA one- and two-wire sensor wiring with terminal markings and circuit legend

02/2019 · A5E34941724-AB, Figure 3-1. Original wiring and block diagram, including terminal numbers, voltage buses and the complete legend.

Supply and isolation

Supply voltage L+

24 V DC

Permissible range: 19.2–28.8 V DC

Reverse polarity protection

Yes

Module current consumption, maximum

70 mA

All channels supplied from the encoder supply

Typical power loss

1.6 W

At 24 V with all 8 inputs supplied via the sensor supply

Sensor supply outputs

8

Sensor supply voltage, minimum

19.2 V

Sensor supply current, maximum

700 mA

Per module and per channel; do not multiply by eight

Sensor supply short-circuit protection

Per module

Channel-to-channel isolation

No

Isolation from backplane bus

Yes

Fault detection and indication

Supply voltage monitoring

Supported

Wire-break diagnostics

Not supported

Sensor-supply short-circuit diagnostics

Not supported

Dedicated channel fault LEDs

No

Channel status LEDs

Green

Supply indication

Green PWR LED

Module indication

Green/red DIAG LED

Basic diagnostics are supply-focused

The module detects missing supply voltage and indicates channel states. It has no wire-break or sensor-supply short-circuit diagnostic reporting, so use a diagnostic-capable module when individual wiring faults must be identified.

Engineering system support

Engineering system support
Parameter / conditionSupported version / integration
STEP 7 TIA PortalV14
STEP 7 ClassicV5.5 SP3
PROFINETGSDML V2.3
PROFIBUSSeparate GSD files, revisions 3 and 5 or later

Address space and functions

Input address space

1 byte

Firmware update

Not supported

Isochronous operation

Not supported

PROFINET R1 interface modules

Suitable for operation

Identification and maintenance data

I&M0 to I&M3

Safety functions

Not supported

Configure the exact module identity

Configure this exact ET 200SP module rather than a visually similar input module. Use the listed engineering-system support for the selected configuration path.

Module dimensions and operating conditions

Dimensions W × H × D

15 × 73 × 58 mm

Electronic module; excludes BaseUnit and packaging

Approximate module weight

28 g

Horizontal operating temperature

−30 to +60 °C

Operation below 0 °C requires hardware status FS03 or later

Vertical operating temperature

−30 to +50 °C

Operation below 0 °C requires hardware status FS03 or later

Maximum installation altitude

5000 m

Above 2000 m, additional installation restrictions apply as described in the ET 200SP system manual

Color code

CC01

Mechanical coding

Type A

Packing unit

1 module

What this order number includes

6ES7131-6BF01-0AA0 identifies the DI 8x24VDC BA electronic module in a one-piece packing unit. Order the type A0 BaseUnit separately for the intended wiring arrangement. This is a standard digital I/O module, not a fail-safe I/O module, interface module or complete ET 200SP station.

Sourcing and order support

Order the exact product and condition your project requires, with assistance from quotation through delivery.

Exact product identification

Your quotation references the complete manufacturer part number to keep the requested product clear.

Condition options

Tell us whether you need new original, new surplus, used, refurbished or repaired equipment.

International delivery

Shipping options are prepared around your destination, quantity and requested delivery date.

Documentation support

Access available manufacturer product data, manuals and certificates associated with the order number.