Exact product identification
Your quotation references the complete manufacturer part number to keep the requested product clear.

XNX-AMSV-NNCB1
ATEX/IEC XNX mV transmitter, 316 stainless steel, M25 entries, 16–32 V DC. Includes MPD catalytic sensor, 0–100% LEL. 4–20 mA with HART.
Warranty coverage and terms are confirmed with your order.
We coordinate the fastest available shipping option for your destination.
Available payment methods are handled through secure payment channels.
Carrier and delivery options are confirmed for your destination before dispatch.
Independent supplier: Xindustra is not an authorized distributor, reseller, or representative of Honeywell. Brand names are used for identification and compatibility purposes only. Read disclaimer
Configuration, sensor-system integration and installation data for XNX-AMSV-NNCB1.
XNX-AMSV-NNCB1 is a complete configured Honeywell XNX transmitter order code: 316 stainless steel housing, ATEX/IEC approval selection, M25 entries and mV input with MPD catalytic sensor. The standard 4–20 mA/HART configuration has no optional output module or local HART port.
XNX-AMSV-NNCB1
ATEX/IEC
M25
316 stainless steel
mV
N — no optional output module
N — not fitted
CB1 — MPD catalytic, 0–100% LEL
M25 threads, ATEX/IEC approval selection and the mV input personality are part of this product’s identity. The 316 stainless steel housing is approximately 5 kg before separately selected sensing equipment. A different personality, entry thread or fitted option changes the ordered configuration.
XNX-AMSV-NNCB1 combines an XNX mV-personality transmitter with an MPD catalytic-bead sensor for 0–100% LEL flammable-gas detection. CB1 identifies the supplied catalytic sensor; it is not an infrared, toxic-gas or oxygen cartridge.
MPD with CB1 catalytic-bead cartridge
Flammable gas concentration
0–100% LEL
20–100% LEL
10% LEL steps in the manufacturer MPD table.
Methane
50% LEL
6.5 W
Documented XNX mV with catalytic/IR cell assembly.
The supplied catalytic sensor measures flammable gases using the catalytic-bead principle. Calibration gas and target-gas response belong to the sensing setup; a %LEL value is not a toxic-gas ppm or oxygen-volume measurement. This CB1 assembly is not the MPD infrared IF1, IV1 or IC1 configuration.
Unlike an XNX code ending NNN, this NNCB1 configuration includes the specified MPD catalytic sensing assembly. The first two N characters mean no optional output module and no local HART port; they do not remove the standard HART-over-current-loop output.
24 V DC
16–32 V DC
4–20 mA with HART
Selectable source, sink or isolated mode
±1% of full scale
Current output accuracy, not gas-sensor measurement accuracy.
0.5–2.5 mm²
Cage-style plug-in terminals with retaining screws.
Magnetic switches; multilingual backlit LCD
Alarm, power and fault LEDs
Account for the connected detector, cable resistance and controller input when choosing the supply and cable. Source/sink/isolated switches are on the rear of the POD; the wiring and current-loop load must match the selected arrangement.
The N option code supplies standard 4–20 mA with HART, without relay, Modbus RTU or FOUNDATION Fieldbus output hardware. Those are other module configurations, not simultaneously available outputs of this exact order code.
HART communication is available over the standard 4–20 mA signal. The local-HART code is N, so this unit does not include the optional externally accessible HART connection port.
316 stainless steel
Marine-grade coating
5 kg
Transmitter housing reference; not a packed shipping weight or a complete remote detector system.
Five M25 entries
Sensor or local-HART hardware occupies an entry when fitted.
Integral surface-mount lugs
Pipe or ceiling mounting with separately selected brackets
IP66 / NEMA 4X
−40 to +65 °C
The selected sensor/detector can impose a narrower operating range.
Original MPD assembly outline
Manufacturer drawing for XNX with MPD sensor, in millimetres. Aluminum outline is shown; the manufacturer notes small stainless-steel body differences with unchanged mounting-hole locations. Applies to the local MPD assembly layout, not a sensorless or remote-detector envelope.
The sensor occupies the lower housing entry and extends below the transmitter body. Keep access to the sensing inlet and calibration connection; the transmitter-body dimensions alone do not describe the installed assembly.
Original transmitter construction
Manufacturer platform construction diagram. The EC barrier is a different personality’s component, not part of this mV input specification. The optional local HART interface shown is not fitted on this N-code model.
XNX-AMSV-NNCB1 uses M25 entries under its ATEX/IEC ordering selection. Use the corresponding certified glands/conduit and stopping plugs. The five housing entries are not five unused cable ports once a sensor or local interface has been fitted.
Manufacturer technical resources for the XNX platform and its ordered input configuration.
Order the exact product and condition your project requires, with assistance from quotation through delivery.
Your quotation references the complete manufacturer part number to keep the requested product clear.
Tell us whether you need new original, new surplus, used, refurbished or repaired equipment.
Shipping options are prepared around your destination, quantity and requested delivery date.
Access available manufacturer product data, manuals and certificates associated with the order number.